Skip to content
D-FENCE Electronic Fencing and Security Systems Ltd.D-FENCE Electronic Fencing and Security Systems Ltd.

The threat · Need a camera up high where there is no pole?

D-Tower

An electric six-section telescopic mast that lifts a 50 kg camera payload to 8.4 m and folds down to 2.174 m.

D-Tower line drawings: the mast extended to 8,407 mm beside the collapsed 2,174 mm mast, side and isometric views and the 790 × 290 mm base plate

No pole on site? Raise one to 8.4 m.

D-Tower is a rapid-deployment observation mast. An electric motor and gearbox extend six telescopic sections from 2.174 m to 8.4 m, lifting up to 50 kg of cameras or sensors on a standard top mount.

01

Height where there is none

Six sections lift cameras from 2.174 m to 8.4 m with an electric motor.

02

Carries a real payload

50 kg rated load on a standard camera top mount.

03

Made for outdoor duty

IP66, powder-coated aluminium and steel, −40 °C to +60 °C.

The mast weighs 74 kg, runs on 24 V DC and bolts down through a 790 × 290 mm base plate. Built from aluminium alloy and steel with a powder-coated finish, it is rated IP66 and operates from −40 °C to +60 °C.

From the first touch to the right response.

  1. Mount

    Bolt the 790 × 290 mm base plate in place.

  2. Equip

    Fit up to 50 kg of cameras on the standard top mount.

  3. Raise

    The 24 V DC motor extends six sections to 8.4 m.

  4. Connect

    Route power and video through the base cable entry to your recorder, VMS or D-Command Control.

Seen in full.

Every image opens full size. Product sheets are shown whole, exactly as D-FENCE publishes them.

Specifications & documents.

SpecificationsD-Tower
Maximum height
8.4 m / 27.56 ft (8,407 mm)
Collapsed height
2.174 m / 7.13 ft (2,174 mm)
Sections
6
Lifting mechanism
Electric motor and gearbox, gear ratio 170:1
Rated load
50 kg / 110 lb
Weight
74 kg / 163 lb
Operating voltage
24 V DC
Material & finish
Aluminium alloy + steel, powder coated
Top mount
Standard camera mount
Base plate
790 mm × 290 mm
Operating temperature
−40 °C to +60 °C / −40 °F to +140 °F
Storage temperature
−40 °C to +70 °C / −40 °F to +158 °F
Protection rating
IP66

Specification text, ready for your tender.

Copy it into your specification. It describes the system by what it must do, so any alternative has to meet every point.

D-TowerTender specification textDatasheet
  1. General

    The system shall be D-Tower by D-FENCE Electronic Fencing and Security Systems Ltd. (ISO 9001:2015 certified quality management), or an approved equivalent that meets every requirement in this section.

  2. Function

    An electric six-section telescopic mast that lifts a 50 kg camera payload to 8.4 m and folds down to 2.174 m.

  3. The system shall provide

    • Electric lift: Electric motor and a 170:1 gearbox raise and lower the six sections.
    • Camera-ready top: Standard camera top mount with a 50 kg rated load.
    • Compact when stowed: Collapses to 2.174 m for transport and storage.
    • Outdoor rated: IP66, powder-coated aluminium alloy and steel, −40 °C to +60 °C.
    • Tidy cabling: Cable entry at the base of the mast.
  4. Technical requirements

    • Maximum height: 8.4 m / 27.56 ft (8,407 mm)
    • Collapsed height: 2.174 m / 7.13 ft (2,174 mm)
    • Sections: 6
    • Lifting mechanism: Electric motor and gearbox, gear ratio 170:1
    • Rated load: 50 kg / 110 lb
    • Weight: 74 kg / 163 lb
    • Operating voltage: 24 V DC
    • Material & finish: Aluminium alloy + steel, powder coated
    • Top mount: Standard camera mount
    • Base plate: 790 mm × 290 mm
    • Operating temperature: −40 °C to +60 °C / −40 °F to +140 °F
    • Storage temperature: −40 °C to +70 °C / −40 °F to +158 °F
    • Protection rating: IP66
  5. Detection sequence

    1. Mount: Bolt the 790 × 290 mm base plate in place.
    2. Equip: Fit up to 50 kg of cameras on the standard top mount.
    3. Raise: The 24 V DC motor extends six sections to 8.4 m.
    4. Connect: Route power and video through the base cable entry to your recorder, VMS or D-Command Control.
  6. Submittals

    Before installation, the contractor shall submit the manufacturer's datasheet, the installation instructions and the zone layout for approval.

Discuss your project.

Tell us the site, the threat and the line. D-FENCE engineers will propose the right barrier, sensor and platform, ready for your integrator.

Build the full line.